DETAIL KOLEKSI

Studi laboratorium pengaruh pemakaian polimer terhadap sifat-sifat fisik lumpur berat dengan sistem non-dispers dalam berbagai temperatur

0.0


Oleh : Bary Jabar Hamidy

Info Katalog

Penerbit : FTKE - Usakti

Kota Terbit : Jakarta

Tahun Terbit : 2015

Pembimbing 1 : Lilik Zabidi

Subyek : Drilling mud operation;Polymer

Kata Kunci : the drilling mud, the drilling fluid, rheology

Status Posting : Published

Status : Lengkap


File Repositori
No. Nama File Hal. Link
1. 2015_TA_TM_07108030_Halaman-judul.pdf
2. 2015_TA_TM_07108030_Bab-1.pdf
3. 2015_TA_TM_07108030_Bab-2.pdf
4. 2015_TA_TM_07108030_Bab-3.pdf
5. 2015_TA_TM_07108030_Bab-4.pdf
6. 2015_TA_TM_07108030_Bab-5.pdf
7. 2015_TA_TM_07108030_Bab-6.pdf
8. 2015_TA_TM_07108030_Daftar-pustaka.pdf
9. 2015_TA_TM_07108030_Lampiran.pdf

D Dalam suatu pemboran perencanaan lumpur pemboran yang akan digunakan sangat menentukan berhasil atau tidaknya pemboran tersebut. Seiring dengan pesatnya perkembangan teknologi lumpur saat ini ditemukan jenis jenis lumpur pemboran dengan karakteristik yang sangat berbeda satu dengan yang lainnya, sebagai akibat dari berkembangnya aditif aditif yang dapat dipakai untuk menjaga kestabilan lumpur pemboran pada tiap tiap kedalaman. Dalam lumpur pemboran juga dikenal pemakaian lumpur polimer yang pada dasarnya termasuk didalam sistem lumpur bahan dasar air. Kelebihan lumpur polimer tersebut disebabkan sistem ini mempunyai sifat rheologi yang baik Tujuan penambahan Polimer XCD, PAC R, dan PAC LV adalah untuk mengurangi dan menstabilkan viskositas lumpur serta membantu dalam mengurangi kehilangan cairan. Sistem penambahan XCD, PAC R, dan PAC LV ini berfungsi untuk mengangkat cutting kembali ke permukaan dan menghasilkan rheology yang baik. Sehingga ketika sirkulasi berhenti, padatan tetap tersuspensi dalam fluida pengeboran. Selain itu,Penambahan XCD, PAC R, dan PAC LV juga berfungsi untuk meningkatkan kemampuan dan penetrasi terhadap material material padat yang kecil dan mengurangi kehilangan tekanan pada saat proses pengeboran berlangsung.Komposisi A adalah yang paling tepat dan telah memenuhi segala spesifikasi yang di tentukan. Pada komposisi ini menggunakan polimer XCD sebesar 1.0 gr, PAC R 0.5 gr, dan PAC LV 0.5 gr.

I In drilling operation, mud drilling that will be used will determine the success or failure of the drilling operation. Along with the rapid technological development of the mud today, found type of drilling mud types with very different characteristics to one another, as a result of the development of many additives that can be used to maintain the stability of each drilling mud in everydepth. In the drilling mud, is also known to use the polymer mud in the basicsystem includes fresh water basic materials mud. Excess sludge resulting thispolymer system has good rheological properties The purpose of XCD polymer, Pac R, and Pac LV addition is to decrease and stabilize the viscosity of the mud and helps to prevent fluid loss. The addition of XCD Polymer, Pac R, and Pac LV system serves to elevate cutting back to the surface and produce value Rheology good low end. So that when the circulation stops, mud still suspended solids in the drilling fluid. Moreover, the addition of XCD Polymer, Pac R, and Pac LV also serve to enhance the capabilities and penetration of the material is small and dense material reduces pressure loss during drilling process took place. Composition A is the most appropriate and meets all specifications as specified. At this composition using the additive XCD Polymer by 1.0 gr, PAC R 0.5 gr, and PAC LV 0.5 gr.

Bagaimana Anda menilai Koleksi ini ?